Are these double knee canvas carpenter pants good for heavy-duty work?

Yes. These pants are built for heavy use because they are made from 12 oz 100% cotton canvas, which provides strong abrasion resistance; they have reinforced double knee panels to protect the highest-wear area; and functional features like multiple tool pockets, a hammer loop, metal trims and rivets add utility and reinforce stress points. They work best for carpenters, construction trades, contractors and DIYers who need hard-wearing bottoms and room to move. Keep in mind they are not waterproof and the metal hardware can be a downside around delicate finishes or in environments where non-conductive gear is required.

How should I choose the right size for these carpenter pants?

They have a loose fit, so pick a size based on your waist measurement and desired roominess. The listed waist ranges are S 30–32, M 34–38, L 40–44, XL 46–50 and 2XL 52–54 inches, with corresponding seat and thigh measurements on the product page to help fine tune fit. If you want a slimmer look size down one size; if you plan to layer over work shorts or wear knee pads, size up. Because they are 100% cotton canvas, expect some initial stiffness and possible minor shrinkage if washed hot, so many people choose their relaxed or true waist size.

How long will these pants last under regular jobsite use?

They are designed to last significantly longer than typical casual pants, but exact lifespan depends on how hard they are used. The 12 oz canvas resists abrasion, double knee reinforcement reduces knee wear, and rivets and metal trims strengthen stress points, so with regular daily trade work you can often expect many months to several years of service. For light weekend or casual use they commonly last multiple years. To maximize lifespan, follow care instructions, avoid unnecessary exposure to harsh chemicals, and repair small seam or knee damage early. Note that extremely abrasive jobs or frequent exposure to moisture will shorten service life.

Are these pants safe for electrical work or jobs with flame risk?

No, these pants are not suitable as protective gear for electrical or flame-hazard work on their own. The metal trims and rivets are conductive and 100% cotton canvas is not inherently flame-resistant unless it has been specifically treated or certified. The tool pockets and hammer loop also increase the chance of metal contact. They are well suited to general carpentry, framing, landscaping and many construction trades that do not require certified protective clothing. For electrical or high-heat environments choose garments with certified flame resistance and non-metallic hardware.

How should I wash and care for the double knee canvas carpenter pants to keep them in good shape?

Yes, you can machine wash them, but follow a few steps to protect fabric and hardware. Turn pants inside out and close any fasteners, wash with like colors on cold or warm using a mild detergent, and avoid bleach which can weaken fibers and corrode metal trims. Tumble dry low or hang dry to reduce shrinkage; ironing on low is fine if needed. Inspect and tighten or repair rivets and seams if you notice wear. Because they are 100% cotton canvas, expect the fabric to soften with washing and to have some shrinkage if washed hot, so washing cool and air drying preserves fit and durability.

Double Knee Canvas Carpenter Pants in andorra

DESCRIPTION

Double knee carpenter pants built for heavy use so your knees get extra protection on the job. They address the common problem of knee wear and early pant failure by adding a second canvas layer at the knees and reinforced hardware so you can work without constant repairs. This item was produced by the number one work apparel manufacturer worldwide, Dickies.

12 oz 100% cotton canvas for abrasion resistance and breathability
Double knee panels with reinforced stitching and metal rivets for extended wear
Loose fit with double front panels allows layering and full range of motion
Multiple work pockets tool pockets hammer loop and metal trims for organized tool carry
Available in Andorra color and sizes S M L XL 2XL see table for waist seat and thigh ranges
Manufactured by Dickies meeting commercial workwear construction standards for daily jobsite use

Measurements in inches Use the table below to compare your waist seat and thigh to a pair you already own. If you plan to layer or wear knee pads choose the larger size for comfort. Unlike slim or fashion pants these are designed for carpentry construction and outdoor maintenance where durability matters. Care: machine wash cold tumble dry low to preserve canvas strength and hardware. See the sizing table below for exact waist seat and thigh ranges to pick the best fit for your work needs.

SHIPPING & RETURNS

Orders are processed within 1–2 business days and ship from our San Francisco hub. Standard U.S. delivery usually takes 3–5 business days.
Need to make a return? No stress, we offer quick and easy returns through our partner app, Redo. Click here to start your return.

1 5

Double Knee Canvas Carpenter Pants in andorra

$82.00

Size 34X32

30X32
32X32
34X32
36X32

Product variants

In stock

DESCRIPTION

12 oz 100% cotton canvas for abrasion resistance and breathability
Double knee panels with reinforced stitching and metal rivets for extended wear
Loose fit with double front panels allows layering and full range of motion
Multiple work pockets tool pockets hammer loop and metal trims for organized tool carry
Available in Andorra color and sizes S M L XL 2XL see table for waist seat and thigh ranges
Manufactured by Dickies meeting commercial workwear construction standards for daily jobsite use